Cat. No. 31-3035/3036
Digital Synthesize
Audio/Video
Surround Receive
STAV-3560/3570
VOLUME
STAV-3560 DIGITAL SYNTHESIZED AUDIO/VIDEO STEREO RECEIVER
PHONO
TUNER
LD/DVD
CD
POWER
TAPE 1
VCR
TAPE 2
MONITOR
SUPER
BASS
SFC
MODE
DOLBY
PRO LOGIC
MIN
MAX
DOLBY SURROUND
MEMORY
FM MONO
CLASS
STATION
P R O
L O G I C
TREBLE
BALANCE
BASS
4-CHANNEL
EQUAL POWER
OUTPUT
PHONES
SPEAKERS
A
B
TUNING
FM/AM
OSR
L
R
VOLUME
STAV-3570 DIGITAL SYNTHESIZED AUDIO/VIDEO STEREO RECEIVER
PHONO
TUNER
LD/DVD
CD
STAND BY
POWER
TAPE 2
MONITOR
VCR
TAPE 1
SUPER
BASS
DOLBY
PRO LOGIC
SFC MODE
MIN
MAX
DOLBY SURROUND
MEMORY
FM MONO
CLASS
FM/AM
STATION
P R O
L O G I C
TREBLE
BALANCE
BASS
4-CHANNEL
EQUAL POWER
OUTPUT
PHONES
SPEAKERS
A
B
TUNING
OSR
L
R
Owner’s Manual
Please read before using this equipment.
IMPORTANT SAFETY INSTRUCTIONS
This receiver is made and tested to meet exacting
safety standards. It meets both UL and FCC require-
ments
Careful attention is devoted to quality standards in the manufacture of your receiver, and safety is
a major factor in its design. However, safety is also your responsibility.
This section lists important information that will help you properly use and enjoy your receiver and
accessories. Read all the included safety and operating instructions before using your receiver. Fol-
low them closely, and retain them for future reference.
To prevent fire or shock hazard, do not expose this sys-
tem to rain or moisture.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for
cleaning. Do not use liquid or aerosol cleaners.
CAUTION
Attachments — Do not use attachments/accessories not recommended by the product manufac-
turer, as they might create a hazard.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION
: TO REDUCE THE RISK OF
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the
product. Follow the manufacturer's instructions for mounting, and use a recommended mounting
accessory.
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure reli-
able operation, and protect from overheating. Do not block or cover these open-
ings, and do not place the product on a bed, sofa, rug, or other similar surface. Do
not place the product in a built-in bookcase or rack unless it provides proper ven-
tilation as specified by the manufacturer.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the system’s enclosure that might be of
sufficient magnitude to constitute a risk of
electric shock. Do not open the system’s
case.
Power Sources — Operate this product using only the power source indicated on its marking label.
If you are not sure of your home's power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade
wider than the other). This plug will fit in the power outlet only one way. This is a safety feature. If
you cannot insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, con-
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polar-
ized plug. If you need an extension, use a polarized cord.
This symbol is intended to inform you that im-
portant operating and maintenance instruc-
tions are included in the literature acc-
ompanying this system.
!
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the product.
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
Lightning — For added protection for this product during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from the wall outlet and disconnect the anten-
na or cable system. This will prevent damage to the product due to lightning and power-line surges.
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles,
as this can result in a risk of fire or electric shock.
CAUTION
Objects and Liquids — Never push objects of any kind into this product through openings, as they
may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Power Lines—Locate an outdoor antenna away from
power lines.
Nonuse Periods—Unplug the receiver’s power cord
when you will not use it for extended periods.
Servicing — Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service person-
Outdoor Antenna Grounding—If an outside antenna
or cable system is connected to the receiver, ground
the antenna or cable system so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 80, provides information about proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See the
example below.
nel.
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qual-
ified service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified techni-
cian to restore the product to normal operation.
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
Antenna
Lead-In
Wire
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Ground Clamp
Safety Check — Upon completion of service or repairs to this product, ask the service technician
Antenna
to perform safety checks to determine that the product is in proper operating condition.
Discharge Unit
(NEC Section 810-20)
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended
by the manufacturer.
Electric
Service
Equipment
Grounding Conductors
(NEC Section 810-21)
Heat — The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
Grounding Clamps
Power Service Grounding
Electrode System
(NEC Article 250, Part H)
NEC -- National Electrical Code
3
Contents
Preparing Your Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Positioning Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting Program Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using One Remote Control for More Than One Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Remote Control’s Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the AC Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tuning the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using FM Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Balance Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Muting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cassette Deck/VCR Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the VCR/TAPE 1 Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the TAPE 2 MONITOR Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Recording a Program Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Dubbing a Cassette Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Playing and Recording Video Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using Advanced Sound Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sound Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Returning Controls to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
The FCC Wants You To Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Index to Features by Control Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4
Preparing Your Receiver
Caution: Make all the necessary connections before you plug in or turn on the receiver.
Where you place your speakers (not supplied) can make a noticeable difference
in your system’s sound. The guidelines in this section will help you choose the
best locations. After you use your receiver for a while, you might want to try dif-
ferent locations for your speakers.
Positioning Speakers
a
L
R
Bass response depends largely on speaker location. For strong bass, place the
speakers in the corners of the room. If you want even stronger bass, place the
speakers directly on the floor. If the bass is too strong, move the speakers
slightly away from the corners of the room, or raise them 6 to 18 inches off the
floor. You can buy speaker stands at your local RadioShack store.
Halfway Point
Between Speake
b
a=b
The distance between the speakers should be about the same as the distance
between the normal listening point and the point halfway between the speakers.
If you place the speakers too close together, you reduce the stereo separation.
If you place them too far apart, you reduce the bass effect and create a hole in
the middle of the sound.
Person in Listening Area
Most speakers have a tweeter dispersion angle of about 60 degrees. Ideally,
your listening position should be just inside the overlap area of the tweeter dis-
persion. You can angle the speakers toward you for better stereo effect.
• Surround speakers generally sound
best if you position them above ear
level.
• To avoid interference with the picture
on a nearby TV, use magnetically
shielded speaker systems. This is par-
ticularly important for the center
speaker since it is usually located
closest to the TV.
To position your speakers for surround sound, place the A or B speakers at the
front of your listening area, and place the surround speakers behind or to the
sides of the listening point (see “Using Advanced Sound Options”). Also, place
the center speaker above, below, or behind the TV. Sound might not appear to
coincide with the picture if you place it beside the TV.
Right Front
Left Front
Center Channel
Listening
Area
Rear Channel
Rear Channel
5
Preparing Your Receiver
Connecting Speakers
Preparing the Speaker Wires
Speaker wire consists of two conductors (individual wires) encased in insulation
and is usually color-coded or marked with a ridge along one side so you can
identify each conductor. Use these markings as a guide to help you properly
connect the speakers to your receiver.
Follow these guidelines when you select
and connect speakers.
• Only connect speakers that are rated
at between 8 and 16 Ohms.
Follow these steps to prepare the speaker wires.
• Be sure you properly connect all
speakers.
Wire Strands
• Do not connect two pairs of speakers
to a single set of terminals (A or B) at
the same time. When you use two
pairs of speakers, connect one set to
Speaker Wire
Speakers A
Speakers B
.
and one set to
• Realistic, Optimus, and other high-
quality speakers have color-coded
speaker terminals (red for positive
polarity and black for negative polar-
ity). Use these color-coded terminals
as a guide to help you properly con-
nect the speakers to the receiver.
Wire Strands
Conductor
1. Cut the speaker wires to the necessary length.
2. Separate the wires about 4 inches on each end.
• Use 16-gauge (or larger) speaker wire
for all speaker connections, and con-
sider possible speaker locations
before you decide how much speaker
wire you need.
3
3. Using a wire stripper, carefully strip about /4 inch of insulation from the
end of each conductor.
4. Twist the end of each conductor to secure any loose wire strands.
Right
Front B Speakers
Front A Speakers
Center Speaker
Left
Right
Left
R
R
L
L
A
B
A
B
AUDIO
IN
FRONT SPEAKERS
L
R
PRE OUT
L
R
SUB
WOOFER
CENTER
SPEAKER
REAR
SPEAKERS
Amplified
Subwoofer
Right
Surround Speakers
Left
6
Preparing Your Receiver
Connecting the A and B Speakers
Note: Be sure you connect the
receiver’s right and left positive (+) and
negative (–) terminals to the speaker’s
corresponding right and left positive (+)
and negative (–) terminals.
Follow these steps to connect the right speaker to the receiver’s right FRONT
SPEAKERS A terminals.
1. Press the receiver’s FRONT SPEAKERS A R (+) red lever and insert the
ridged or color-coded conductor’s end into the small hole. Pull back the
lever to secure the conductor.
2. Press the receiver’s FRONT SPEAKERS A R (–) black lever and insert the
other conductor’s end into the small hole. Pull back the lever to secure the
conductor.
3. Connect the ridged or color-coded conductor’s loose end to the right
speaker’s positive (+) terminal.
4. Connect the remaining loose conductor to the right speaker’s negative (–)
terminal.
Repeat Steps 1 through 4 to connect the left speaker to the receiver’s FRONT
SPEAKERS A L terminals.
Repeat this entire process to connect a second pair of speakers to the FRONT
SPEAKERS B terminals.
Connecting Surround-Sound Speakers
You can connect a pair of speakers to the receiver’s REAR SPEAKERS terminals
for surround-sound programs. Follow the steps in “Connecting the A and B
Speakers.”
Connecting the Center Speaker
The center speaker gives additional ambience to surround sound. Connect the
center speaker to the CENTER SPEAKER terminals. Follow the steps in “Con-
necting the A and B Speakers.”
Connecting a Subwoofer Amplifier (STAV-3570 Only)
Your receiver includes a line-level subwoofer output. Connecting a subwoofer to
your system dramatically extends bass response for incredible richness and
depth. When you listen to surround-sound programs, a subwoofer enhances
your home theater experience by realistically recreating the rumble of an earth-
quake, the bone-jarring percussion of a cannon, and more.
To use this output, simply connect it to an amplified subwoofer’s line-level input
or to an amplifier connected to a subwoofer.
RadioShack stores sell a variety of suitable subwoofers and amplifiers.
7
Preparing Your Receiver
You can connect up to five external program sources to your receiver at one
time.
Connecting Program Sources
OUT
IN
IN
TO MONITOR TV
VIDEO OUT
VIDEO
PLAY
IN
REC
OUT
IN
IN
IN
L
L
L
OUT
R
R
R
TAPE2
MONITOR
VCR/
TAPE 1
LD/
DVD
CD
CONTROL
PHONO
GND
LINE
LINE
PLAY
REC
REC
PLAY
REC
REC
OUT PUT
L
L
L
R
R
PLAY
PLAY
R
INPUT OUTPUT
INPUT OUTPUT
CD
Cassette Deck
Turntable
Cassette Deck
CD Player
Connecting a Turntable
Connect a turntable with a magnetic cartridge only. Some older turntables use a
ceramic-type cartridge that does not work with this system.
Note: Use shielded audio cables with
phono connectors for all audio connec-
tions.
Connect the turntable’s left and right cables to the receiver’s left and right
PHONO
GND
jacks. Then connect the turntable’s ground wire to the receiver’s
terminal.
Connecting Cassette Deck(s)
VCR/TAPE 1
TAPE 2 MONITOR
and the
You can connect cassette decks to the
Note: If you place the cassette deck
directly above, below, or to the left of the
receiver, the receiver could interfere with
the cassette deck’s operation. If possi-
ble, position the cassette deck to the
right of the receiver or locate it away
from the receiver.
VCR/TAPE 1 IN
jacks. Connect the cassette deck’s output jacks to the
(audio) or
TAPE 2 MONITOR PLAY
jacks, and connect the cassette deck’s input jacks to the
VCR/TAPE 1 OUT
TAPE 2 MONITOR REC
jacks.
(audio) or
LD/DVD IN
You can connect a third cassette deck (for playback only) to the
(audio) jacks.
Connecting a CD Player
To connect a CD player to the receiver, connect the CD player’s left and right
R CD IN
L
output jacks to the receiver’s and
jacks.
8
Preparing Your Receiver
Connecting Video Sources
If you connect two video sources such as VCRs, laser disc (LD) players, or dig-
ital video disc (DVD) players to your receiver, you can use the receiver to switch
between viewing the sources. You can also use the receiver to easily record
from the video sources to the source connected to VCR/TAPE 1.
Note: If your VCR is monaural, use a Y-
adapter (available at your local
RadioShack store) to connect the VCR’s
audio output to both the L and R audio
inputs on the receiver.
OUT
IN
IN
TO MONITOR TV
VIDEO OUT
VIDEO
PLAY
IN
REC
OUT
IN
IN
IN
L
L
OUT
R
R
TAPE2
MONITOR
VCR/
TAPE 1
LD/
DVD
CD
CONTROL
PHONO
GND
VIDEO
AUDIO
PLAY
AUDIO
OUT
VIDEO
OUT
REC
VIDEO
IN
OUT
IN
L
L
R
R
REC
PLAY
INPUT OUTPUT
VCR
VCR
LD/DVD Player
TV Monito
Connect phono cables from a VCR’s audio outputs to the receiver’s VCR/TAPE 1
or LD/DVD IN (audio) jacks. Then connect phono cables from the receiver’s VCR/
TAPE 1 OUT (audio) jacks to the VCR’s audio input jacks.
Connect video cables from each video source’s video outputs to the receiver’s
VCR/TAPE 1 or LD/DVD VIDEO IN jacks. Then connect video cables from the
receiver’s VCR/TAPE 1 VIDEO OUT jack to the VCR’s video input.
Connecting a Video Monitor
The monitor (or TV with baseband video input) you connect to the VIDEO OUT
terminal can monitor any program you connect to the receiver’s VCR/TAPE 1 or
LD/DVD input jacks. Connect a video cable from the receiver’s VIDEO OUT TO
MONITOR TV jack to the monitor’s video input.
9
Preparing Your Receiver
Connecting the Antennas
In many cities, the supplied indoor AM loop and FM antennas provide adequate
reception.
AM Antennas
Assemble the included antenna’s base by swinging the base in the direction of
the arrow and inserting the antenna’s bottom tabs into the base’s slot. Then
AM LOOP ANTENNA
GND
terminals (bottom
attach the antenna wires to the
two terminals).
and
Place the antenna on a flat surface and rotate it for the best AM reception.
If the receiver is in a rack or on a shelf and there is no room for the AM loop
antenna, use two screws (not supplied) to mount the base on the wall or
another location as shown.
Notes:
• Keep the AM loop antenna connected even when you use another indoor
antenna or an outdoor AM antenna.
• Ensure the antenna does not touch the receiver or other metal objects.
AM Loop Antenna
FM
UNBAL 75
AM
• Do not place the antenna near a CD player, a personal computer, or a TV
set
LOOP ANTENNA
GND
GND
• If the wire between your AM loop antenna and receiver is too short, you
can add extra wire, available at your local RadioShack store.
ANTENNA
You can also use a RadioShack shortwave antenna kit (Cat. No. 278-
758), which makes an excellent outdoor AM antenna.
Outdoor AM Antenna
FM
AM
UNBAL 75
LOOP ANTENNA
GND
GND
Connect the outdoor AM antenna wire to the receiver’s AM terminal, as shown.
ANTENNA
FM Antennas
FM UNBAL 75
Connect the supplied FM antenna to the
as shown.
Ω terminal and extend it
AM Loop Antenna
FM Antenna
FM
UNBAL 75
AM
LOOP ANTENNA
GND
GND
ANTENNA
For better FM reception, you can also use a rabbit-ear TV antenna (for indoor
use only) or an outdoor VHF TV antenna. To connect the TV antenna to the
receiver, you need a VHF/UHF/FM splitter (not included). RadioShack stores
carry a full line of quality outdoor antennas and antenna connection accesso-
ries.
Note: For the best results, use 75-ohm
coaxial cable to connect an outdoor
antenna to the receiver.
10
Preparing Your Receiver
For the best radio reception, use an outdoor antenna. Follow these steps to
connect an outdoor FM antenna to the receiver using 75Ω cable.
Warning: To prevent injury, read and fol-
low all cautions and warnings that
accompany the outdoor antenna.
Note: If your antenna has 300Ω twin-lead cable, consult your local RadioShack
store for the correct adapter.
FM UNBAL 75
1. Disconnect the supplied FM antenna from the receiver’s
terminal.
Ω
2. With a stripping tool, remove about 11/2 inches of the 75Ω cable’s outer
insulation to expose the cable’s shielding.
3. Fold back the insulation from the inner insulation.
4. Remove about 1 inch of the inner insulation from around the center wire.
Inner Insulation
Center Wir
Outer Insulation
Shielding
FM
5. Pull the shielding to one side. Connect the center wire to the receiver’s
Caution: The cable’s shielding should
UNBAL 75
Ω terminal. Twist the shielding to secure any loose wire strands,
GND
only touch the
terminal.
GND
and connect it to the
terminal.
FM Outdoor Antenna
Shielded
FM
UNBAL 75
AM
Core
LOOP ANTENNA
GND
GND
ANTENNA
Note: Grounding is not necessary for reception, but we recommend it to avoid
damage from lightning when you use an outdoor FM antenna and for better FM
reception. Use a separate piece of thick polyvinyl insulated wire to connect the
GND
terminal to an earth ground such as a metal cold-water pipe.
Warning: Never connect a wire to a gas pipe for grounding since sparks might
ignite the gas.
11
Preparing Your Receiver
If you also have an Optimus professional series CD player, VCR, or cassette
CONTROL IN
so you can control all of your equipment with a single remote control. You can
also use the other component’s remote control by pointing it at the receiver’s
front panel.
Using One Remote Control
for More than One Unit
deck with the OSR mark, you can connect its
jack to the receiver
Note: When you plug the cable into a
CONTROL IN
component’s remote sensor does not
function.
component’s
jack, that
1. Connect each component to the receiver as shown in “Connecting Pro-
gram Sources.”
CONTROL
Note: You must connect the audio cables between the receiver and the
other audio accessory to use your receiver’s remote control to ccontrol
the accessory.
IN
OUT
OUT
CONTROL
2. Connect the cable supplied with the CD player, VCR, or cassette deck
CONTROL OUT
between the receiver’s
CONTROL IN
jack and the other component’s
jack.
Other Component
with OSR Mark
Receiver
3. When you want to control more than one other component using the
CONTROL OUT CONTROL
receiver’s remote control, daisy-chain the
IN
and
Remote
Control
To the CONTROL IN ja
of Another Componen
Having the OSR Mark
connections as shown.
The remote control uses two AA batteries (not included). For the longest battery
life, we recommend alkaline batteries (such as RadioShack Cat. No. 23-557).
Installing the
Remote Control’s Batteries
1. Press and remove the battery compartment cover.
2. Place two fresh AA batteries in the compartment as indicated by the
polarity symbols (+ and –) marked in the compartment.
Cautions:
• Use only fresh batteries of the recom-
mended size and type.
3. Replace the battery compartment cover.
• Always remove old or weak batteries.
Batteries can leak chemicals that can
damage electronic circuits.
Note: If the remote’s range is reduced,
replace the batteries immediately.
12
Preparing Your Receiver
Your receiver has an AC power outlet that you can use to power an electronic
device, such as a turntable, cassette deck, VCR, and so on. This switched out-
let turns on and off with the receiver and provides a maximum of 100 Watts.
Using the AC Power Outlet
Caution: Do not connect appliances with
high power consumption, such as a
heater, iron, monitor, or TV, to this AC
outlet. Doing so can cause a risk of over-
heating and fire, and could damage the
receiver.
Before you plug in the receiver’s power cord, double check all other connec-
tions.
Connecting to AC Power
To power the receiver, plug the supplied power cord into a standard AC outlet.
The power cord’s plug is polarized and fits only one way.
Warning: To prevent electric shock, do
not use this polarized plug with an exten-
sion cord, receptacle, or other outlet
unless you can fully insert the blades to
prevent blade exposure.
R
R
L
L
A
B
A
B
CAUTION: DO NOT CONNECT TV SET OR MONITOR.
FRONT SPEAKERS
L
R
AC 120V 60HZ
PRE OUT
SWITCHED
100W MAX
0.8A MAX
L
R
SUB
WOOFER
AC OUTLET
CENTER
SPEAKER
REAR
SPEAKERS
13
Basic Operation
Note: The controls on the remote control work the same as the buttons on the
receiver’s front panel.
Warning: To prevent possible hearing
loss, turn VOLUME to MIN before you turn
on the receiver or change the program
sources. After you turn on the receiver or
change the program source, adjust VOL-
UME to a comfortable listening level.
Follow these steps to use the receiver.
1. Press POWER to turn on the receiver’s power. It takes about 5 seconds to
begin hearing sound.
2. Select the speakers.
FRONT SPEAKERS A
B
If you connected speakers only to the
(or ) ter-
SPEAKERS A (or B) to turn on only those speakers.
minals, press
FRONT SPEAKERS A
B
If you connected speakers to both the
and ter-
minals, do any of the following:
•
•
•
Press in SPEAKERS A or B to turn on either pair of speakers for a two-
speaker stereo effect.
Note: If you want to find out what a par-
ticular button or control is used for, see
Page 22 (for the remote control) or Page
29 (for the front panel) to find the page
where the button or control is described.
Press in SPEAKERS A and B to turn on both pairs of speakers for a
four-speaker stereo effect.
Press SPEAKERS A and B to the out position to silence all speakers
and listen privately with headphones (see “Using Headphones” on
Page 16).
3. Select a program source.
To tune to a radio station, see “Tuning the Radio” on Page 16.
TAPE 2 MONI-
To listen to signals from the component connected to
Note: If you select a source while TAPE 2
MONITOR is engaged, TAPE 2flashes
five times on the display, reminding you
to disengage the TAPE 2 MONITOR func-
tion.
TOR press TAPE 2 MONITOR so TAPE 2appears on the display.
,
TAPE 2 MONITOR
To listen to a source other than one connected to
,
be sure TAPE 2does not show on the display. If necessary, press TAPE
2 MONITOR so TAPE 2disappears.
Then press VCR/TAPE 1, LD/DVD (laser disc/digital video disc), CD,
TUNER, or PHONO, or repeatedly press FUNCTION on the remote control,
to display the desired program source.
4. Adjust VOLUME clockwise to increase the volume and counterclockwise
to decrease it. Or, you can use MASTER VOLUME –/+ on the remote con-
trol.
5. Use the BASS and TREBLE controls to adjust the program’s tonal quality.
To enhance the bass level, press SUPER BASS.
6. Adjust BALANCE to suit your listening preferences. See “Balance Control”
on Page 15.
7. Press POWER to turn off the receiver.
14
Basic Operation
Tuning the Radio
Your receiver offers three types of electronic tuning — manual, automatic, and
memory.
Manual and Automatic Tuning
Note: For weak signals, we recommned
manual tuning.
Follow these steps to manualy or automatically tune to the stations.
TUNER
FM/AM
to select the desired band.
1. Press
. Then press
The receiver tunes to and displays the frequency last selected in that
band.
TUNING
2. Press
or once to manually select the next higher or lower fre-
TUNING
quency. Or, press and hold down
or to rapidly change freqe-
uncies. Release the button to stop.
TUN-
To automatically search for the next higher or lower station, release
ING
as soon as the display starts to change. The receiver seaches up or
down the band to the next strong station.
Notes:
• STEREOappears on the display for FM stereo broadcasts. TUNED
appears on the display when you tune to a strong station. To find a
FM MONO
weak FM station, press
FM Mono” on Page 16.
until MONOappears. See “Using
TUNING
TUNING
•
If you press
at the top of the frequency range or
at the bottom of the frequency range, the display returns to the other
end of the range.
Memory Tuning
Memory tuning lets you instantly tune to a stored frequency. You can store up to
10 AM or FM frequencies in any of the three classes — up to 30 frequencies
total.
Follow these steps to store a station.
TUNER
FM/AM
to select the desired band.
1. Press
. Then press
2. Using either manual or automatic tuning, select the frequency you want to
store.
Notes:
• If you store a frequency in a memory
that already contains a frequency, you
replace the previous frequency.
FM MONO
If desired, press
for FM monaural sound (see “Using FM Mono”
on Page 17). This setting is stored in the memory.
• If your receiver is disconnected from
AC power for several days, it loses all
the stored frequencies.
MEMORY
3. Press
. MEMORYlights, and -- chand the class number (1, 2,
or 3) flash on the display for about 5 seconds.
CLASS
4. While MEMORYis on the display, press
want (1-3) appears on the display. Then press
until the class number you
STATION
or until the
station number you want appears on the display. The station number
lights steadily, indicating the receiver memorized the frequency.
Repeat these steps to store additional frequencies.
CLASS
To tune to a stored frequency, press
so the desired class number
STATION
/
appears on the display, then press
to select the station.
15
Basic Operation
FM MONO
To receive FM stations in stereo, press
until MONOdisappears from
Using FM Mono
Balance Control
the display. STEREOappears on the display when you receive an FM broadcast
in stereo.
FM MONO
You can improve the reception of weak FM stations by pressing
MONOappears. This reduces noise while you listen to a weak FM station, but
you get monaural instead of stereo sound.
until
BALANCE
The
control lets you adjust the sound balance between the left and
right speakers. If you properly position the speakers and your listening area is
centered between them, the center control setting is usually best (see “Position-
ing Speakers” on Page 5).
BALANCE
For an unusual speaker placement, adjust
as follows:
to select the FM band.
until MONOappears. The sound is monaural instead of
TUNER
FM/AM
1. Select
. Then press
FM MONO
2. Press
stereo, so each speaker delivers the same output.
BALANCE
3. Turn
until you hear the sound coming equally from each
speaker when you are in the listening area.
FM MONO
4. Press
until MONOdisappears from the display.
MUTING
To temporarily mute the sound, press
on the remote control. MUTING
again to restore the audio level.
Muting the Receiver
Using Headphones
MUTING
appears. Press
1
To listen with headphones (not supplied), insert the headphones’ /4-inch plug
PHONES
A
into the receiver’s front panel
jack. To silence the speakers, set and
B SPEAKERS
to the out position and turn off any special sound options.
Listening Safely
To protect your hearing, note the following when using headphones.
• Set the volume to its lowest setting before you begin listening. After you
begin listening, adjust volume to a comfortable level.
• Do not listen at extremely high volume levels. Extended high-
volume listening can lead to permanent hearing loss.
• Once you set the volume, do not increase it. Over time, your ears adapt to
the volume level, so a volume level that does not cause discomfort might
still damage your hearing.
16
Cassette Deck/VCR Features
You can connect two cassette decks to the receiver. Selecting either VCR/TAPE
1 or TAPE 2 MONITOR lets you hear the playback from the cassette deck you
connected to the receiver’s corresponding (VCR/TAPE 1, TAPE 2 MONITOR)
jacks.
Press VCR/TAPE 1. VCRappears on the display. You hear the playback from the
cassette deck or VCR you connected to the receiver’s VCR/TAPE 1 IN jacks.
Using the VCR/TAPE 1
Button
Press TAPE 2 MONITOR. TAPE 2appears on the display along with the last
program source you selected. You can hear playback or monitor a recording
from the cassette deck you connected to the receiver’s TAPE 2 MONITOR jacks.
Using the TAPE 2
MONITOR Button
The TAPE 2 REC jacks continue to output the previously selected source when
you press TAPE 2 MONITOR.
To return to the previous source, press TAPE 2 MONITOR again so TAPE 2dis-
appears.
Notes:
• If you press TAPE 2 MONITOR when that cassette deck is neither playing
nor recording, the receiver mutes the current audio source. To hear the
audio source, press TAPE 2 MONITOR until TAPE 2disappears from the
display.
• Do not press TAPE 2 MONITOR while you are recording on the deck con-
nected to TAPE 2 REC. If you do, the recording is interrupted for about 1
second.
The receiver sends the audio program source you select—VCR/TAPE 1, TAPE 2
MONITOR, CD, TUNER, PHONO—to the VCR/TAPE 1 OUT (audio) and TAPE 2
MONITOR REC jacks (if you select VCR/TAPE 1 or LD/DVD, the audio and video
program are also sent to the TO MONITOR TV jacks).
Recording a Program Source
Dubbing a Cassette Tape
The VOLUME control does not affect the level of the signal going to the tape
decks.
You can copy, or dub, a cassette tape from one cassette deck to another.
You can use either deck as the playback or recording deck. However, if you
want to monitor the cassette deck during dubbing, use the deck connected to
the VCR/TAPE 1 jacks as the source, and the deck you connected to the TAPE 2
REC jacks as the recording deck. Then press TAPE 2 MONITOR until TAPE 2
and the last program source you selected appear on the display. See “Using the
TAPE 2 MONITOR Button.”
17
Cassette Deck/VCR Features
You can connect two video sources to the receiver. If you connect a VCR to the
Playing and Recording
Video Tapes
VCR/TAPE 1
LD/DVD
audio and video jacks, you can copy video cassette
and
tapes from one VCR to another and monitor the dubbing process.
Playing a Video Cassette Tape
VCR/TAPE 1
To play a video tape, load the tape into the VCR connected to either
LD/DVD
VCR/TAPE 1
LD/DVD
or ) that corresponds to the
or
. Press the button (
jack the VCR is connected to. VCRor LD/DVDappears on the display. Follow
the VCR’s instructions to begin playback. If you connected a monitor to the
TO MONITOR TV
receiver’s
jack, you can view the program on that monitor.
Copying a Video Cassette Tape
Follow these steps to copy a video tape from one VCR to another.
LD/DVD
1. Load the tape you want to copy into the VCR connected to
.
2. Load a blank tape (or one you want to record over) into the VCR con-
VCR/TAPE 1
nected to the
jacks.
LD/DVD
3. Press
.
4. Begin recording and playback on the VCRs.
18
Using Advanced Sound Options
Your receiver has four special sound options: Dolby Pro-Logic Surround, Dolby
3CH Logic, Studio-Effect Surround, and Simulated Surround. These special
options enhance a program source.
Notes:
• To get the full benefit from programs
encoded with Dolby Surround Sound,
you need a stereo VCR.
Notes:
To activate Dolby Pro-Logic Surround or Dolby 3CH Logic, press DOLBY PRO
LOGIC, then press CENTER MODE on the remote control to select the Dolby Pro-
Logic options (normal, wide, or phatom) or Dolby 3CH Logic. For studio effect or
simulated surround, press SFC MODE until the desired option appears on the
display. On the remote control, press SURR MODE to select the sound options;
when you select the Dolby Pro-Logic, use CENTER MODE to make a selection
(see “Sound Mode Adjustments (Remote Control Only)” on Page 20).
• Dolby Surround does not operate cor-
rectly if the signal passes through a
graphic equalizer. If you connected an
equalizer to the TAPE 2 MONITOR
jacks, do not select TAPE 2 MONITOR
when you listen to Dolby Surround sig-
Dolby Pro-Logic Surround
Dolby Pro-Logic Surround puts you in the middle of the action. The center- and
rear-channel speakers add incredible realism by directing the sound to the
appropriate speakers, making you feel like you are really there. You can find
hundreds of movies, television shows, and compact discs produced with Dolby
Surround.
Dolby 3CH Logic
Dolby 3CH Logic produces a more spacious sound field than is possible with
ordinary stereo playback, by combining the front and rear speaker sounds.
Select this mode when you play a Dolby Surround Sound program and do not
have rear speakers. The rear channel’s sound is sent to the front left and right
speakers.
Studio Effect
Studio Effect gives the effect of listening in a recording studio. The front speak-
ers provide normal stereo, and the rear speakers provide a subtly reverberated
sound. Select this mode when you listen to sources not encoded with Dolby
Surround.
Simulated Surround
Simulated Surround simulates a surround effect when you listen to a monaural
(mono) source.
19
Using Advanced Sound Options
Center Mode Setting
Sound Mode Adjustments
(Remote Control Only)
The center mode setting affects the center channel’s bass signals. It operates
only when you select the Dolby Pro-Logic Surround or Dolby 3CH Logic mode.
CENTER MODE
Each time you press
on the remote control, the setting changes
Note: If you do not use a center speaker,
the monaural signals are only repro-
duced if you select PHANTOM.
and the receiver’s corresponding indicator lights: NORMAL, WIDE, or PHAN-
TOMDolby Pro-Logic Surround options, or 3CH LOGIC.
NORMAL—Select this mode if you use a small center speaker. The front left and
right speakers play the center-channel bass sounds.
WIDE—Select this mode if you use a medium or large center speaker. The cen-
ter speaker plays the center-channel bass sounds.
PHANTOM—Select this mode if you have no center speaker. All center-channel
sound comes from the front left and right speakers.
Test Tone
The test tone feature provides a test tone that lets you balance the signal levels
between all your speakers. To adjust the levels, see “Center Level” and “Rear
Level.”
To activate the test tone, select one of the surround sound modes and set
AUDIO SURROUND
SURROUND TEST TONE
. Then press . The
•
on the remote to
receiver sounds a 2-second tone from the front left, center, front right, and rear
speakers, in sequence. The center test tone sounds only when you select the
Dolby Pro-Logic Surround or Dolby 3CH Logic Sound mode.
In the Dolby 3CH Logic Sound mode, the receiver sounds a 2-second tone from
the left, center, and right speakers, in sequence.
TEST TONE
Press
again to turn off this feature.
Center Level
AUDIO SURROUND AUDIO
to
– CENTER LEVEL +
to adjust the
Slide
•
. Then press
center speaker sound level while in the Dolby Pro-Logic Surround or Dolby 3CH
Logic mode.
Notes:
VOLUME
• Use the
control to adjust the
overall sound level.
Rear Level
• Set the center mode to a selection
other than PHANTOM before adjusting
the center level.
AUDIO SURROUND
SURROUND
– REAR LEVEL +
. Then press to adjust
Slide
•
to
the rear speakers’ sound level while in the Dolby Pro-Logic Surround or Simu-
lated Surround mode.
Delay Time
In the Simulated Surround and Dolby Pro-Logic Surround modes, the receiver
slightly delays the sound going to the rear speakers. You can change the delay
time from 5 to 30 milliseconds (ms) in 2 ms steps. Adjust this for the best sur-
round effect.
Notes:
• For Dolby Pro-Logic Surround, the
delay is preset to 5 mS.
• The delay time does not affect the Stu-
dio Effect mode.
AUDIO SURROUND
SURROUND
DELAY TIME
. Then press and hold to
Slide
•
to
change the delay time. The receiver displays the selected time.
20
Using the Remote Control
The remote control works up to a distance of about 23 feet, and within a 30-
degree angle on either side of the receiver. Point the control at the receiver’s
front panel and press the desired button(s).
Many buttons on the remote control work the same as buttons on the receiver’s
front panel. Use these buttons exactly as you would use the corresponding but-
tons on the receiver.
•
AUDIO SURROUND Switch
Set the switch to AUDIO to control audio components such as CD players or
cassette decks. Set the switch to SURROUND when setting the surround sound
options.
SURROUND
AUDIO
ASMS
When you set the switch to SURROUND, dual-function buttons control the func-
tion marked in gold next to the button. For example, the button marked TEST
TONE and RETURN operates as the test tone function when you set the switch to
SURROUND and returns the system to default settings when you set the switch
to AUDIO.
CD
RANDOM
BEST
DISC
DECK1
DECK2
TAPE
STATION
CLASS FM MONO
TAPE2
REAR
Receiver/Amplifier Section
FUNCTION
LEVEL
MONITOR
Receive
Amplifie
Section
CENTER
LEVEL
SURR
MODE
MUTING
FUNCTION
Selects a program source (VCR/Tape 1, LD/DVD, CD, tuner,
FUNCTION
TEST
DELAY
TIME
CENTER
MODE
TONE
or phono). Repeatedly press
until the display
RETURN
S.BASS
shows your desired program source. See Page 14.
POWER
CD
MASTER
VOLUME
RECEIVER
TAPE
– MASTER VOLUME +
CENTER MODE
Adjusts the system’s volume. See Page 14.
AUDIO/VIDEO
SYSTEM REMOTE
OSR
Selects among the three center modes or 3CH Logic. See
Page 21.
– CENTER LEVEL +
– REAR LEVEL +
TEST TONE
Controls the relative volume of the center speaker with
AUDIO•SURROUND
AUDIO
. See Page 21.
set to
Controls the relative volume of the rear speakers with
AUDIO•SURROUND SURROUND
set to
. See Page 21.
AUDIO•SUR-
. See Page 21.
Sets the rear-channel delay for Dolby Pro-Logic Surround
Sounds test tones from each speaker with
ROUND SURROUND
set to
DELAY TIME
AUDIO•SURROUND
and Simulated Surround programs with
SURROUND
set to
. See Page 21.
SURR MODE
Selects between Dolby Pro-Logic Surround or Simulated Sur-
round sound. See Page 20.
RECEIVER POWER
RETURN
Turns the receiver on and off. See Page 14.
AUDIO•SUR-
Returns the receiver to its default settings with
ROUND AUDIO
set to
. See Page 24.
TAPE 2 MONITOR
S. BASS
Switches the receiver to monitor the source connected to the
TAPE 2 MONITOR
jacks. See Page 18.
AUDIO•SURROUND
Press to enhance bass sound with
AUDIO
set
to
.
MUTING
Silences the receiver. Press again to restore the sound to its
previous level. See Page 15.
STATION
CLASS
Press to move the next higher or lower station in memory.
Press to select the class of the station in memory
FM MONO
Press to disable the FM stereo mode to improve reception of
weaker FM stations.
21
Using the Remote Control
CD Player Section
Before operation, set AUDIO•SURROUND to AUDIO.
CONTROL OUT
Note: You must connect the CD changer both to your receiver’s
and audio jacks for these functions to work.
CD POWER
Turns the CD player on and off (only for CD players having
the CONTROL IN/OUT feature).
|
ASMS
|
Returns to the beginning of the current track or advances to
the next track.
DISC SELECT
Selects discs in a multi-play CD changer.
Note: Some CD players might not function with DISC
SELECT.
SURROUND
AUDIO
ASMS
Plays the CD.
CD
CD Player
Section
Stops play.
RANDOM
BEST
DISC
Press to temporarily stop play. Press again to resume.
Starts random playback.
DECK1
DECK2
RANDOM
BEST
TAPE
Tape Sectio
With a CD changer that has a BEST track memory function,
such as an Optimus Professional Series CD-8200/8300/
8400, press to select and play your favorite CD track.
STATION
CLASS FM MONO
TAPE2
REAR
FUNCTION
LEVEL
MONITOR
CENTER
LEVEL
SURR
MODE
MUTING
TEST
DELAY
TIME
CENTER
MODE
Tape Section
TONE
RETURN
S.BASS
POWER
CD
MASTER
VOLUME
RECEIVER
TAPE
Before operation:
AUDIO/VIDEO
SYSTEM REMOTE
• Set AUDIO•SURROUND to AUDIO.
OSR
• For a dual cassette deck, select DECK 1 or DECK 2. If you use a single
cassette deck, press DECK 2.
• You must connect the cassette deck both to your receiver’s CONTROL
OUT and audio jacks for these functions to work.
Press to start normal play.
Press to play the reverse side of an auto-reverse cassette
deck.
Press to temporarily stop playback/recording. Press again to
resume.
Press to stop the operation.
and
Lets you quickly locate and play the beginning of recorded
material during play.
When the tape is stopped, lets you rapidly search forward or
backward to locate a specific section of the tape.
DECK 1/DECK 2
TAPE POWER
Selects Deck 1 or Deck 2 when you use a dual cassette deck.
Turns on/off the cassette deck.
Note: TAPE POWER does not work with all Optimus Profes-
sional Series cassette decks.
22
Troubleshooting
If the receiver is not working as it should, the following suggestions might help. If you follow the suggestions in this chart and
the receiver still does not work properly, contact your local RadioShack store for assistance.
Problem
Cause
Solution
• Plug in the power cord.
Power does not turn on.
• Power cord is disconnected.
• Protection circuit is activated.
• Unplug the power cord, then plug it in
again.
The receiver does not respond to
button presses.
• Static discharge has affected con- • Unplug the power cord, then plug it in
trol.
again. (If static electricity is a problem, use
the remote control as much as possible.)
No sound.
• Incorrect connections.
• Check and correct the connections.
• Press MUTING.
• The mute function is activated.
• The volume is turned down.
• Speaker wires are disconnected.
• Neither set of speakers is selected.
• Turn up the volume.
• Connect the speaker wires.
• Press in SPEAKERS A or B.
No picture when you select a video • The selected video source is not set • Correct the problem with the selected
source.
correctly.
video source.
• Incorrect connections.
• Station not correctly tuned.
• Antenna not connected.
• Correct the connections.
• Tune to a stronger station.
• Connect the antenna.
High noise level.
• FM antenna still coiled or is not • Stretch both ends of the antenna taut and
pointing in the correct direction. reposition the antenna.
• AM loop antenna not pointing in the • Adjust the AM loop antenna.
correct direction.
• Noise is coming from another elec- • Try using an AC line noise filter to reduce
trical appliance.
the noise.
Tuning does not automatically stop
when searching for FM stations.
• Stations are too weak.
• Use a better antenna.
Cannot make copies of video
tapes.
• Tapes are protected by a copy • You cannot make a good copy.
restriction method.
• Video connections are incorrect.
• Check and correct the connections.
Remote does not control cassette
deck or CD player.
• Cassette deck or CD player is not • The feature only works with Optimus Pro-
compatible.
fessional Series components.
• Control cable is not plugged in.
• Audio cables are not plugged in.
• Properly connect the control cable.
• Properly connect the audio cables.
Press RETURN to return the controls to the following settings.
Returning Controls to
Factory Defaults
Tape 2 Monitor
Source
Off
TUNER
FM (Set to the last-tuned frequency. If the receiver
cannot receive the frequency, it starts searching for
the next strong station.)
Band
Surround Mode
Muting
Off
Off
Off
Super Bass
23
Care and Maintenance
Your Optimus STAV-3560/3570 Digital Synthesized A/V Surround Receiver is an example of superior design and craftsman-
ship. The following suggestions will help you care for the receiver so you can enjoy it for years.
Keep the receiver dry. If it gets wet, wipe it dry immediately. Liquids can contain
minerals that can corrode the electronic circuits.
Handle the receiver gently and carefully. Dropping it can damage its circuit
boards and can cause the receiver to work improperly.
Use and store the receiver only in normal temperature environments. Tempera-
ture extremes can shorten the life of electronic devices, damage batteries, and
distort or melt plastic parts.
Keep the receiver away from dust and dirt, which can cause premature wear of
parts.
Wipe the receiver with a damp cloth occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or strong detergents to clean the
CLEANER
receiver.
Use only fresh batteries of the recommended size and type in the remote con-
trol. Always remove old or weak batteries. They can leak chemicals that can
destroy electronic circuits.
Modifying or tampering with your receiver’s internal components can cause a malfunction and might invalidate the receiver’s
warranty and void your FCC authorization to operate it. If the receiver is not operating as it should, take it to your local
RadioShack store for assistance.
24
The FCC Wants You To Know
Your receiver might cause radio or TV interference even when it is operating
properly. To determine whether your receiver is causing the interference, turn off
your receiver. If the interference goes away, your receiver is causing it. Try to
eliminate the interference by:
• Moving your radio or TV away from the receiver
• Connecting your receiver to an outlet that is on a different electrical circuit
from the radio or TV
• Contacting your local RadioShack store for help
If you cannot eliminate the interference, the FCC requires that you stop using
your receiver.
25
Specifications
Amplifier
Front Channel Average Power Output . . . . . . . . . . . . . 100 Watt (STAV-3570)/60 Watts (STAV-3560) per Channel into 8 Ohms
From 40 to 20,000 Hz,
With No More than 0.9% Total Harmonic Distortion
Measured Pursuant to the Federal Trade Commission’s
Trade Regulation Rule on Amplifier Output Power Claims
Front Channel Surround Power Output . . . . . . . . . . . .70 Watts per Channel (STAV-3570)/60 Watss per Channel (STAV-3560)
Center Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Watts (STAV-3570)/60 Watts (STAV-3560)
Continuous Rear Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Watts (STAV-3570)/60 Watts (STAV-3560)
per Channel (1 kHz, 0.8% THD, 8 Ohms)
Dynamic Power Output (2 Ohms/4 Ohms/8 Ohms) . . . . . . . . . . . . . . . . . . . . . . . . 170 Watts/160 Watts/130 Watts (STAV-3570)
110 Watts/100 Watts/70 Watts (STAV-3560)
Input Sensitivity/Impedance
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/47 kOhms
CD, LD/DVD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kOhms
Phono Overload Level (0.1% THD, 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mV
Frequency Response
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .20 Hz to 20,000 Hz ±0.3 dB
CD, LD/DVD, VCR/TAPE 1, TAPE 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hz to 100,000 Hz +0/–3 dB
Output Level/Impedance
VCR/TAPE 1 REC, Tape 2 Monitor REC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kOhms
Tone Controls
Bass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (150 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (10 kHz)
Super Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+8 dB (80 Hz)
Signal-to-Noise Ratio (IHF, Short Circuited, A Network)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 dB
CD, LD/DVD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 dB
Signal-to-Noise Ratio (EIA, at 1 Watt, 1 kHz)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 75 dB
CD, LD/DVD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 dB
Video Section
Input Sensitivity/Impedance VCR/TAPE 1, LD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Output Level/Impedance VCR/TAPE 1, Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Frequency Response VCR /TAPE 1, LD/DVD Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hz to 7 MHz +0/–3 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
26
Specifications
FM Tuner
Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5 to 108 MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono: 11.2 dBf, IHF (1.0 µV/75 Ohms)
50 dB Quieting Sensitivity
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.8 dBf (1.9 µV/75 Ohms)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.6 dBf (23.3 µV/75 Ohms)
Signal-to-Noise Ratio
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 dB (at 85 dBf)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB (at 85 dBf)
Distortion Stereo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB (400 kHz)
Stereo Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Hz to 15 kHz (±1 dB)
Antenna Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Ohms Unbalanced
AM Tuner
Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1700 kHz
Sensitivity (IHF, Loop Antenna) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
General
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Volts AC, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Watts, 300 VA (UL)
AC Outlet Ratings Switched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total 100 Watts (0.8 Amps) Maximum
Dimensions (HWD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51/2 × 169/16 × 1215/16 Inches
(140 × 420 × 328 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 lbs, 13 oz (7.2 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
27
Index to Features by Control Name
This table lists the control and indicator names found on the front of your receiver, along with the page number where the con-
trol or indicator is discussed. To find a description for the buttons on the remote control, see “Using the Remote Control” on
Page 22.
Control
Page
BALANCE
BASS
16
14
BEST
22
CD
14
CLASS
15
FM MONO
FM/AM
16
15
LD/DVD
MEMORY
MUTING
NORMAL
PHANTOM
PHONES
PHONO
POWER
RANDOM
RETURN
SELECT
SFC MODE
14
15
16
20
20
16
14
14
22
23
15
19
SPEAKERS A and B
SUPER BASS
TAPE 2 MONITOR
TREBLE
14
14
14, 17
14
TUNER
15
TUNING
15
VCR/TAPE 1
VOLUME
14, 17
14
WIDE
20
28
Notes
29
Notes
30
Notes
31
RadioShack Limited Warranty
This product is warranted against defects for 2 years from date of purchase from
RadioShack company-owned stores and authorized RadioShack franchisees and deal-
ers. Within this period, we will repair it without charge for parts and labor. Simply bring
your RadioShack sales slip as proof of purchase date to any RadioShack store. War-
ranty does not cover transportation costs. Nor does it cover a product subjected to mis-
use or accidental damage.
EXCEPT AS PROVIDED HEREIN, RADIOSHACK MAKES NO EXPRESS WARRAN-
TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states
do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limi-
tation(s) or exclusion(s) may not apply to the purchaser.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
We Service What We Sell
9/94
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
<ARB1484-A>
7A6
Printed in Malaysia
|
Milwaukee Coffee Grinder 4931 User Manual
MSi Computer Hardware MS 6775 v1x User Manual
Multiquip Power Roller MDR 9GH User Manual
National Instruments Network Card Ultiboard User Manual
NETGEAR Switch FS728TP User Manual
NordicTrack Home Gym NTSA03990 User Manual
NordicTrack Treadmill NTL270050 User Manual
Panasonic Server KX NCP User Manual
Panasonic Wireless Office Headset KX TDE100 User Manual
ParaBody Home Gym 872101 User Manual