OPERATOR’S MANUAL
NP828C01-1
RELEASED:
REVISED:
(REV. 01)
5-2-03
INCLUDING: SPECIFICATIONS, PUMP DATA, SERVICE KITS
INCLUDE MANUALS: Refer to list below.
8” AIR MOTOR
28:1 RATIO
NP828C01-1
Pump and Cart Assembly
6” STROKE
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
DO NOT EXCEED MAXIMUM WORKING PRESSURE OF 3360 P.S.I. (231.7 BAR) AT 120
P.S.I. 8.3 BAR) AIR INLET PRESSURE.
SERVICE KITS
PUMP DATA
•
Use only genuine AROR replacement parts to assure compatible
pressure rating and longest service life.
29960 for repair of 27354Ć000 regulator.
66614 for repair of 66523ĆB air motor.
104020 for repair of 25351Ć010 filter.
104023 for repair of 26351Ć010 lubricator.
637098ĆR43 for repair of 66475ĆR4D lower pump section.
637103 for repair of 651533 spray gun.
NP828C01Ć1 Pump and Cart Assembly
•
•
•
•
•
•
OPERATING AND SAFETY PRECAUTIONS
WARNING READ THE GENERAL INFORMATION MANUAL
INCLUDED FOR OPERATING AND SAFETY PRECAUTIONS
AND OTHER IMPORTANT INFORMATION.
GENERAL DESCRIPTION
The ARO model NP828C01Ć1 pump and cart assembly is designed to
provide portability to a pump that is primarily used for airless spray apĆ
plications. Materials of light Ć medium viscosity are best suited for the
unit.
IMPORTANT
This is one of the fourteen documents which support the various compoĆ
nents of the system. Replacement copies are available upon request.
= NP828C01Ć1 Model Operator's Manual (pn 97999Ć1024)
- 650865ĆXĆB TwoĆBall Pump (pn 97999Ć878)
- SĆ636 General Information Ć Pumping Systems (pn 97999Ć636)
- 66475āĆX Lower Pump End (pn 97999Ć111)
Figure 1
- 66523ĆB Air Motor (pn 97999Ć868)
- 66554ĆX Heavy Duty Cart (pn 97999Ć574)
OPERATION
- 66559 Check Valve (pn 97999Ć315)
- 65030ĆXĆB Filter and Swivel Assembly (pn 97999Ć587)
- 651533ĆX Spray Gun (pn 97999Ć83)
See 650865ĆXĆB pump manual installation for flushing instructions. AfĆ
ter the pump has been flushed with a compatible solvent and is ready for
operation:
- 651418ĆXĆB Material Filter (pn 97999Ć8)
1. Place 66728 suction hose into material.
- 651728ĆX FĆRĆL Accessory Kit (pn 97999Ć419)
- WARNING Ć High Pressure Equipment (pn 97999Ć540)
- 253XXĆX Heavy Duty Filter Ć Regulator Ć Lubricator (pn 103942)
- SĆ632 General Information Ć Industrial Piston Pumps (pn 97999Ć624)
2. Connect air line to 651728Ć1 Filter Ć Regulator Ć Lubricator.
3. Turn knob on air regulator clockwise to start pump.
4. Allow pump to cycle slowly and prime with material. This will bleed
trapped air from the system.
INSTALLATION
The unit comes completely assembled.
INGERSOLL-RAND COMPANY
P.O. BOX 151 D ONE ARO CENTER D BRYAN, OHIO 43506Ć0151
& (419) 636-4242 D FAX (419) 633-1674
E2003
CCN 20051306
|